Share

Monday, April 4, 2016

Toyota 4Runner Keyfob Keyless Remote Programming Instructions

Keyfob Keyless Remote Programming Instructions are used to teach a new remote's codes to your vehicle.


Toyota 4Runner Remote Keyless Entry Programming Instructions

2010 2011 2012 2013 2014 2015 2016 Toyota 4Runner:  These vehicles require an automotive locksmith or dealer to perform programming on your vehicle using special equipment.
Toyota 4Runner Remote Head Key
Toyota 4Runner Smart Key Remote 
_________________________________________________
2003 2004 2005 2006 2007 2008 2009 Toyota 4Runner:  
  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other doors don’t matter).
  2. Perform the next two steps within 5 seconds:
    1. Insert the key into the ignition (don’t turn it) and pull it out.
    2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Insert the key into the ignition (don’t turn it) and pull it out.
  4. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Insert the key into the ignition.
    4. Close the driver’s door.
    5. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
    6. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
    2. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
  7. Open driver’s door.
Toyota 4Runner Remotes

_________________________________________________
2002 Toyota 4Runner with Factory and Dealer Installed System:

  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other door locks don’t matter).
  2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
    2. Close, then open the driver’s door.
  4. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously). 
    2. Insert Key in ignition.
    3. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    4. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
    2. Immediately after letting go of the LOCK and UNLOCK buttons, press the LOCK button by itself and release.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
    3. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
  7. Close driver door.
Toyota 4Runner Remotes
_________________________________________________
2001 Toyota 4Runner with Factory Installed System:

  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other door locks don’t matter).
  2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
    2. Close, then open the drivers door.
  4. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously). 
    2. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    3. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    4. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
    2. Immediately after letting go of the LOCK and UNLOCK buttons, press the LOCK button by itself and release.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
    3. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
  7. Close driver door.
Toyota 4Runner Remotes

_________________________________________________

2001 Toyota 4Runner with Dealer Installed System:
  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other door locks don’t matter).
  2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
    2. Close, then open the driver’s door.
  4. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously). 
    2. Insert Key in ignition.
    3. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    4. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
    2. Immediately after letting go of the LOCK and UNLOCK buttons, press the LOCK button by itself and release.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
    3. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
  7. Close driver door.

_________________________________________________
1999 2000 Toyota 4Runner with Factory Installed System:

  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other door locks don’t matter).
  2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
    2. Close, then open the drivers door.
  4. Perform these steps within 40 seconds:
    1. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously). 
    2. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    3. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
    4. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
    2. Immediately after letting go of the LOCK and UNLOCK buttons, press the LOCK button by itself and release.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
    3. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.
  7. Close driver door.
Toyota 4Runner Remotes
_________________________________________________

2000 Toyota 4Runner with Dealer Installed System:
  1. Start with the following conditions: 
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other doors don’t matter).
  2. Perform the next two steps within 5 seconds:
    1. Insert the key into the ignition (don’t turn it) and pull it out.
    2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Insert the key into the ignition (don’t turn it) and pull it out.
  4. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Close the driver’s door.
    4. Insert the key into the ignition.
    5. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
    6. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
    2. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release.  Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming.  If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
    3. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.
  7. Open driver’s door.
Toyota 4Runner Remotes
_________________________________________________

1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 Toyota 4Runner with Dealer Installed System:

1. Insert the key into the ignition, and turn it to the ON position (as far as you can go without cranking the engine).
2. Press and hold the receiver PROGRAMMING SWITCH/BUTTON for 3 seconds (see figure).  In some cases the button cannot be accessed with a finger – use a pencil or similar narrow object to poke through the Programming Button access hole.  For most vehicles, the receiver is located underneath either the driver or passenger front seats.  On others it is behind the driver’s dash. In the case of some Camry’s, the receiver can be accessed by gently prying out the black faceplate behind the mirror control switch.  The black faceplate is approx. 5 inches wide by 3 inches tall.   
3. The STATUS MONITOR LED (on dash or center console) turns on for 5 seconds.   For some vehicles, a double chirp of the horn is heard instead of the flashing light.
4. Within 5 seconds of lighting the status MONITOR LED, press and release the transmitter’s TOP or BOTTOM button (either button on your REMOTE CONTROL can be programmed to operate the system - the other button can be programmed to operate a second Toyota vehicle with the same system). 
5. The STATUS MONITOR LED turns off, the Piezo chirper chirps once, and the exterior lights flash once.  In some cases, the only response is a single horn chirp.
6. To program an additional remote, repeat steps 2-4.
7. Turn OFF the ignition.

Important Components of RS-3000 VIP System
Toyota 4Runner Remotes


1 comment:

  1. Ian can provide locksmithing services for 90% of vehicles on the road. If you're locked out of your car or truck or need a new set of keys cut, give Cambridge Locksmiths a call today. It can be very inconvenient and distressing to be locked out of your property or your car. With so many years in the trade, Ian has seen it all and is an expert at unlocking anything that uses a key. If you're locked out, call the expert at www.flatratelocknkey-denver.com

    Call Ian today, and he’ll be happy to give you a free quote for any locksmithing services you require. He can also arrange for an on-site inspection if you’d like some friendly advice on the best types of locks for your property.

    ReplyDelete